Changing a bathe arm is a comparatively easy plumbing process that may be accomplished in beneath an hour with the appropriate instruments and somewhat little bit of know-how. Whether or not you are upgrading your showerhead or just changing a worn-out arm, following these step-by-step directions will guarantee a profitable set up.
Earlier than you start, collect the required instruments and supplies: a brand new bathe arm, adjustable wrench, plumber’s tape, and a bucket. Begin by turning off the water provide to the bathe. As soon as the water is off, take away the outdated bathe arm by unscrewing it from the wall. Be sure you use a wrench to keep away from damaging the threads. As soon as the outdated arm is eliminated, clear the threads on the wall with a moist fabric and apply just a few wraps of plumber’s tape.
Now, take the brand new bathe arm and screw it onto the wall. Hand-tighten the arm as a lot as attainable, then use the wrench to additional tighten it. Watch out to not over-tighten the arm, as this might harm the threads. As soon as the arm is safe, reattach the showerhead. Activate the water provide and verify for any leaks. If there aren’t any leaks, your new bathe arm is efficiently put in.
Disassembling the Previous Bathe Arm
Your bathe arm is probably going connected to a threaded pipe contained in the wall. To take away it, you will have to shut off the water provide and use a pair of pliers or a wrench to loosen and take away the bathe arm.
Listed below are some detailed steps on disassemble the outdated bathe arm:
- Shut off the water provide. There are usually two water provide strains that run to the bathe valve. Find the shut-off valves for these strains and switch them clockwise to shut them. As soon as the water is shut off, you’ll be able to proceed to the following step.
- Take away the showerhead. Unscrew the showerhead from the bathe arm by turning it counterclockwise. If the showerhead is caught, you should use a pair of pliers or a wrench to loosen it.
- Cowl any uncovered threads with Teflon tape. Teflon tape helps to seal the threads and forestall leaks. Wrap the tape across the threads in a clockwise route, ranging from the highest of the threads and dealing your approach all the way down to the underside.
Upon getting ready the bathe arm for elimination, you’ll be able to observe these further steps:
- Loosen the bathe arm nut. Utilizing a pair of pliers or a wrench, fastidiously loosen the nut that’s holding the bathe arm in place. Watch out to not overtighten the nut, as this may harm the bathe arm or the pipe.
- Take away the outdated bathe arm. As soon as the nut is loosened, you need to be capable to pull the bathe arm straight out of the pipe. If the bathe arm is caught, you should use a pair of pliers to softly pull it out.
- Clear the pipe. As soon as the outdated bathe arm is eliminated, you need to clear the pipe to take away any particles or corrosion. You should use a rag or a brush to wash the pipe.
Upon getting disassembled the outdated bathe arm, you’ll be able to set up the brand new bathe arm by following the steps in reverse order.
Take away the Escutcheon Plate
The escutcheon plate is the ornamental protecting that conceals the bottom of the bathe arm. Earlier than you’ll be able to change the bathe arm, you’ll want to take away the escutcheon plate.
To take away the escutcheon plate, you have to a flat-head screwdriver.
Comply with these steps to take away the escutcheon plate:
- Flip off the water provide to the bathe.
- Find the escutcheon plate on the base of the bathe arm.
- Insert the flat-head screwdriver into the slot between the escutcheon plate and the wall.
- Gently pry the escutcheon plate away from the wall. Watch out to not harm the wall or the escutcheon plate.
| Instruments You will Want |
|---|
| Flat-head screwdriver |
| Adjustable wrench |
| Pipe wrench |
Unscrew the Bathe Arm
The following step is to unscrew the bathe arm from the pipe. To do that, you have to a wrench. Place the wrench on the hexagonal nut on the base of the bathe arm and switch it counterclockwise. If the nut is tight, it’s possible you’ll want to make use of a pair of pliers that can assist you flip it. Proceed turning the nut till the bathe arm is totally indifferent from the pipe.
As soon as the bathe arm is indifferent, you’ll be able to take away the outdated washer from the bottom of the bathe arm. The washer is a small, rubber ring that helps to seal the bathe arm to the pipe. If the washer is broken or worn, it will probably trigger the bathe to leak. Change the outdated washer with a brand new one.
Now you’ll be able to screw the brand new bathe arm onto the pipe. To do that, place the brand new washer on the bottom of the bathe arm after which screw the bathe arm onto the pipe. Flip the bathe arm clockwise till it’s hand-tight. Then, use the wrench to tighten the bathe arm additional. Watch out to not overtighten the bathe arm, as this might harm the pipe.
As soon as the bathe arm is tightened, you’ll be able to reattach the showerhead. To do that, merely screw the showerhead onto the bathe arm. Flip the showerhead clockwise till it’s hand-tight. Then, use the wrench to tighten the showerhead additional. Once more, watch out to not overtighten the showerhead, as this might harm the bathe arm.
Cleansing the Bathe Pipe
Cleansing the bathe pipe is a vital step in changing a bathe arm, as it’ll assist to take away any grime or particles that might stop the brand new arm from becoming correctly. To scrub the bathe pipe, you have to:
- A pair of pliers
- A mushy fabric
- A non-abrasive cleaner
- A small brush (elective)
Directions:
- Flip off the water provide to the bathe.
- Take away the outdated bathe arm by loosening the set screw that holds it in place. Use the pliers to grip the set screw and switch it counterclockwise till it’s free.
- Pull the outdated bathe arm off the bathe pipe.
- Clear the bathe pipe utilizing a mushy fabric and a non-abrasive cleaner. If there may be any cussed grime or particles, you should use a small brush to softly scrub it away.
- Rinse the bathe pipe totally with water.
- Dry the bathe pipe with a clear fabric.
Making use of Plumber’s Tape
Plumber’s tape, also referred to as Teflon tape, is a skinny, white tape created from polytetrafluoroethylene (PTFE). It’s used to seal threads on pipes and fittings to stop leaks. To use plumber’s tape accurately:
- Clear the threads on each the pipe and the becoming with a clear fabric.
- Begin the tape on the finish of the threads, closest to the becoming.
- Wrap the tape clockwise across the threads, overlapping every layer by about half.
- Proceed wrapping the tape till you attain the top of the threads.
- Don’t overtighten the tape. It must be comfortable, however you need to nonetheless be capable to flip the becoming by hand.
- As soon as the tape is utilized, you’ll be able to insert the becoming into the pipe and tighten it.
- Test for leaks and tighten the becoming additional if needed. At all times verify the producer’s suggestions for the precise software.
Ideas for Making use of Plumber’s Tape
Listed below are just a few suggestions for making use of plumber’s tape accurately:
- Use solely high-quality plumber’s tape.
- Wrap the tape within the route of the threads.
- Overlapping the tape by about half will guarantee a superb seal.
- Don’t overtighten the tape. It must be comfortable, however you need to nonetheless be capable to flip the becoming by hand.
- Test for leaks and tighten the becoming additional if needed.
Set up the New Bathe Arm
As soon as the outdated bathe arm is eliminated, it is time to set up the brand new one. Listed below are the detailed steps:
1. Wrap the Bathe Arm Threads
Apply plumbers’ tape clockwise across the threads of the brand new bathe arm. Begin from the top of the threads and work your approach in the direction of the opposite finish. Wrap a number of layers of tape, about 5-7 occasions.
2. Test and Clear the Wall Becoming
Examine the wall becoming the place the bathe arm will probably be put in. Take away any outdated tape or particles. You should use a wire brush or a pipe cleaner to wash the threads.
3. Apply Pipe Joint Compound
If desired, apply a skinny layer of pipe joint compound on the threads of the wall becoming. It will assist create a watertight seal.
4. Screw the Bathe Arm into the Wall Becoming
Align the bathe arm with the wall becoming and hand-tighten it clockwise so far as attainable. Keep away from overtightening.
5. Use a Wrench to Tighten
Utilizing an adjustable wrench, tighten the bathe arm additional. Apply agency stress however watch out to not harm the threads.
6. Set up the Showerhead
As soon as the bathe arm is securely in place, connect the showerhead by hand-tightening it clockwise.
7. Test for Leaks
Activate the water provide and verify for leaks. If there are any leaks, tighten the bathe arm or showerhead connections additional.
8. Wrap the Bathe Arm Base
For added safety and to stop water from seeping behind the bathe arm and inflicting harm, wrap a layer of plumbers’ tape across the base the place it connects to the wall. Begin from the highest and work your approach down, overlapping the layers barely. Then, apply a bead of clear silicone caulk across the base to create a watertight seal.
Reattach the Escutcheon Plate
As soon as the bathe arm is secured, you’ll want to reattach the escutcheon plate to cowl the opening within the wall and provides your bathe a completed look. This is how:
-
Align the escutcheon plate with the opening within the wall and slip it over the bathe arm.
-
Tighten the screws that maintain the escutcheon plate in place. Do not overtighten them, as this might harm the plate or the wall.
-
Test for any gaps between the escutcheon plate and the wall. If there are any, use a bead of caulk to seal them.
-
Wipe away any extra caulk with a moist fabric.
-
Enable the caulk to dry fully earlier than utilizing your bathe.
| Tip |
|---|
| Should you’re undecided how tight to tighten the screws, begin by hand-tightening them till they’re comfortable. Then, use a screwdriver to show them an extra quarter flip. |
Activate the Water Provide and Test for Leaks
As soon as the brand new bathe arm is in place, activate the water provide to the bathe. Test for any leaks on the connection between the pipe and the bathe arm. Should you discover any leaks, tighten the connection till the leak stops. It is essential to be sure that the connection is watertight to stop harm to the wall or ceiling behind the bathe.
Steps to Test for Leaks:
- Activate the water provide to the bathe.
- Test the connection between the pipe and the bathe arm for leaks.
- Should you discover any leaks, tighten the connection till the leak stops.
- As soon as you have tightened the connection, flip off the water provide and verify for leaks once more.
- If there aren’t any leaks, you are all set!
| Steps | Particulars |
|---|---|
| Activate water provide | Guarantee ample water stress for testing. |
| Test for leaks | Observe the connection space for water droplets or seepage. |
| Tighten connection (if wanted) | Use a wrench or pliers to safe the bathe arm to the pipe. |
| Flip off water provide | Halt water circulate for additional inspection and changes. |
| Affirm no leaks | Confirm full absence of water leakage earlier than continuing. |
How To Change A Bathe Arm
Changing a bathe arm is a comparatively easy plumbing process that may be accomplished in just a few steps. This is do it:
- Flip off the water provide to the bathe.
- Take away the outdated bathe arm by unscrewing it from the wall.
- Apply plumber’s tape to the threads of the brand new bathe arm.
- Screw the brand new bathe arm into the wall.
- Activate the water provide and verify for leaks.
Individuals Additionally Ask
How do I do know if my bathe arm must be changed?
There are just a few indicators that point out your bathe arm could must be changed, together with:
- The bathe arm is leaking.
- The bathe arm is free.
- The bathe arm is corroded.
What instruments do I would like to exchange a bathe arm?
You have to the next instruments to exchange a bathe arm:
- Adjustable wrench
- Plumber’s tape
- New bathe arm
